Gelcoat, paint thinners and hardener into gelcoats

Showing 1-15 of 15 item(s)

Clear Epoxy Gelcoat EG 100-T - for thin layers

eshop_001045

This epoxy gelcoat can be applied solely by spraying. It can also be applied as a brush coating. The secret to smooth surfaces. It creates a smooth visible layer depending on the surface of the mold. The surface does not require any further treatment after being removed from the mold.

Kč1,142.00

Epoxy gelcoat 7060 clear

eshop_900882

UV stabilized transparent epoxy gelcoat for the visible layer of carbon parts, more information in TL and BL:

Kč1,541.70

Epoxy Gelcoat for Mold Production Araldit SW 404

eshop_001052

Top-quality gelcoat for mold production. Blue in color, it is known for its unmatched durability and time-tested quality. The only disadvantage is that it cannot be polished. Chemically resistant. For curing, use hardener Araldit HY 2404 in a ratio of 100:10. Curing time

Kč1,188.85

-Kč59.23

Epoxy gelcoat for mold production F 200 /MGS/

001054

Can be sanded and polished. Any repairs are easily feasible. Recommended hardener F 250, mixing ratio gelcoat: hardener= 100:25 by weight. Suitable for molds laminated with epoxy resin. After curing, it must be lightly sanded before further laminating for d

Kč631.80 Kč691.03

Time left

Epoxy Gelcoat P for Mold Production, Black

eshop_001061

Creates a solid surface and edges of molds, is polishable and has a black color. After mixing, we recommend vacuuming in a prepared bell to remove microbubbles formed during mixing. Recommended hardeners EPH 161 (VE 3261) and EPH 573 (VE 2723). The coverage is 0.5-1 kg/m2

Kč1,256.20

Epoxy gelcoat white spray EG 100-W - for thin layers

eshop_001044

A solution of medium molecular weight epoxy resin in a mixture of organic solvents with the addition of additives, white shade RAL 9003. This epoxy gelcoat can be applied solely by spraying. It can also be applied as a brush coating. The secret of smooth p

Kč1,054.15

Epoxy Resin Surface Araldite SW 419-1

eshop_001074

Areas of use . tools for sheet forming . general mold production Processing methods Application using a brush or spatula Characteristic features . well spreadable . does not run . minimal sedimentation For curing, it is necessary to mix Hardener HV 2419 in

Kč951.67

Hardener 7067 for gelcoat

eshop_900883

Hardener for transparent gelcoat 7060, more information in TL and BL.

Kč1,434.82

-Kč127.47

Hardener F 250 /MGS/

001057

Hardener for curing molding resin F 200. The mixing ratio is 100:25 /by weight/. Processing time 100g/25 C 15-20min., gel time 1 mm. 1-2 h., curing at 25 C 24 h. Hardener F 250 is suitable for use in the production of molds without the requirement for thermal curing.

Kč764.84 Kč892.31

Time left

Hardener H 100 for epoxy spray gelcoat EG 100-W and EG 100-T

eshop_001046

Hardener for epoxy gelcoats. Mixing for EG 100 T: H100= 100:40 and for EG 100 W:H100= 100:26 by weight. Mix the gelcoat and hardener in the prescribed ratio and stir thoroughly. Only then can it be diluted if necessary. Do not load until the coating is fully cured.

Kč1,200.56

Hardener HV 2419

eshop_001075

Hardener designed for epoxy gelcoat Araldite SW 419-1\nMixing ratio 100:13 /by weight/

Kč1,839.79

Hardener HY 2404

eshop_001053

Hardener for curing epoxy gelcoat Araldit SW 404 Mixing ratio 100:10 /by weight/ working time 25-30 min.

Kč1,672.59

Hardener REN HY 5159 for RENGEL SW 56

eshop_001123/2

Hardener for the molding gelcoat SW 56. Recommended dosage of hardener HY 5159 in the ratio epoxy:hardener= 100:10 (by weight). After gradual tempering, heat-resistant up to 120°C, the processing time at 25°C and 250ml is 25-30 min.

Kč2,459.69

High-Temperature Epoxy Resin Araldit SW 18

eshop_001052/2

Green polishable epoxy gelcoat for mold making for hand lamination, vacuum infusion, and RTM, also suitable for the production of polyester parts (gelcoat resistant to styrene). For curing, use hardener Araldit HY 5159 in a weight ratio of 100:16.

Kč1,603.19

Thinner for epoxy spray gelcoat EG 100-W and EG 100-T

eshop_001047

Thinner for epoxy solvent-based coatings. An addition of 5-20% thinner will significantly change the viscosity of the gelcoat, making it suitable for spraying. A larger amount may significantly alter the properties of the cured gelcoat.

Kč500.72