Epoxy and Polyester RESINS, HARDENERS AND GELCOATS

Showing 109-120 of 132 item(s)

HAVELPOL - 5 CLEAR non-accelerated!

eshop_000040/6

HAVELpol 5 polyester resin is suitable for the production of strength-demanding parts that must withstand greater loads. Note that the resin is not pre-accelerated - A CATALYST AND ACCELERATOR ARE REQUIRED FOR CURING! To cure, add the Peroxi catalyst

Kč316.25

HAVELPOL -1

eshop_000040/2

Basic orthophthalic resin, pre-accelerated, thixotropic and simultaneously low-emission. It is suitable for products that do not require high strength. For lamination, basic peroxides such as Butanox M 50 or peroxide K 1 are suitable. Basic mixing ratio 100:1-2 (note it is not a sou

Kč209.37

HAVELPOL -2 - new formulation

eshop_000040/3

Standard orthophthalic polyester resin HAVELpol 2. It is a pre-accelerated polyester resin developed for hand lamination or spraying. For curing, add peroxide K1 or Butanox M50 in a ratio of 100:1-3 by weight. Pot Life at 1% Butanox

Kč346.99

High-Temperature Epoxy Resin Araldit SW 18

eshop_001052/2

Green polishable epoxy gelcoat for mold making for hand lamination, vacuum infusion, and RTM, also suitable for the production of polyester parts (gelcoat resistant to styrene). For curing, use hardener Araldit HY 5159 in a weight ratio of 100:16.

Kč1,603.19

LH 260 with Defoamer

eshop_112218/1

General: Epoxy resin LH 260 with defoamer contains added substances based on a silicone-free defoamer suitable for all applications. The defoamer allows for faster removal of microbubbles from the future composite. Epoxy resin LH 260 is

Kč531.47

Peroxid SF 10 - MGS

eshop_000012

Peroxide recommended for curing MGS gelcoats SF 30, T 30, T 35, T 3 PU, applied by spraying.

Kč2,150.47

Peroxide K1 for curing polyester resins

eshop_000021

The best in the resins we offer. Please do not try untested ones, it is risky and very costly! Recommended mixing ratio 0.8-3% depending on the ambient temperature and the thickness of the laminated part.

Kč398.60

Polyester Gelcoat White GS 2000 H - Norpol

eshop_000016

The secret of smooth surfaces. It creates a smooth visible layer depending on the surface of the mold. The surface does not require any further treatment after removal from the mold. We create the surface directly in the mold. The paintable gelcoat is a two-component system, mix 1-3 before use.

Kč514.63

Polyester gelcoat/Vorgelat/ T 30 - MGS - clear

eshop_000008/a

Gelcoat with high scratch resistance. For curing, use Peroxide SF 10, resin to peroxide mixing ratio=100:10. Workability 25min. Gel time 150min. Full curing 5-6 hours, final state after 2-3 days at room temperature. For coloring is

Kč1,445.36

Polyester gelcoat/Vorgelat/ T 35 - MGS

eshop_000010/1

Specially developed gelcoat for aircraft manufacturing with excellent parameters. Available only in white. For best results, we recommend using original peroxides and thinners. Can be diluted with SF thinner up to 10 weight parts. Pigments can be used for coloring.

Kč1,288.41

Polyester Gelcoat/Vorgelat/ T 35 SH - MGS

eshop_000010/2

Equivalent to polyester gelcoat T 35 - SH variant. The working procedure is the same as for T 35. Due to its thinner consistency, this type is particularly suitable for spray application. SH means that a thinner SH has already been added to the gelcoat.

Kč1,295.73

Polyester Resin Havelpol H 834 - REA 30W

eshop_000040/32

!!New formula - different resin color!!\n\nPolyester resin H 834 is a medium-reactive thixotropic, pre-accelerated with controlled exotherm and low shrinkage. It is intended for the production of boats and other composite parts, suitable for both manual application.

Kč316.25