Epoxy and Polyester RESINS, HARDENERS AND GELCOATS

Showing 109-132 of 132 item(s)

HAVELPOL - 5 CLEAR non-accelerated!

eshop_000040/6

HAVELpol 5 polyester resin is suitable for the production of strength-demanding parts that must withstand greater loads. Note that the resin is not pre-accelerated - A CATALYST AND ACCELERATOR ARE REQUIRED FOR CURING! To cure, add the Peroxi catalyst

Kč316.25

HAVELPOL -1

eshop_000040/2

Basic orthophthalic resin, pre-accelerated, thixotropic and simultaneously low-emission. It is suitable for products that do not require high strength. For lamination, basic peroxides such as Butanox M 50 or peroxide K 1 are suitable. Basic mixing ratio 100:1-2 (note it is not a sou

Kč209.37

HAVELPOL -2 - new formulation

eshop_000040/3

Standard orthophthalic polyester resin HAVELpol 2. It is a pre-accelerated polyester resin developed for hand lamination or spraying. For curing, add peroxide K1 or Butanox M50 in a ratio of 100:1-3 by weight. Pot Life at 1% Butanox

Kč346.99

High-Temperature Epoxy Resin Araldit SW 18

eshop_001052/2

Green polishable epoxy gelcoat for mold making for hand lamination, vacuum infusion, and RTM, also suitable for the production of polyester parts (gelcoat resistant to styrene). For curing, use hardener Araldit HY 5159 in a weight ratio of 100:16.

Kč1,603.19

LH 260 with Defoamer

eshop_112218/1

General: Epoxy resin LH 260 with defoamer contains added substances based on a silicone-free defoamer suitable for all applications. The defoamer allows for faster removal of microbubbles from the future composite. Epoxy resin LH 260 is

Kč531.47

Peroxid SF 10 - MGS

eshop_000012

Peroxide recommended for curing MGS gelcoats SF 30, T 30, T 35, T 3 PU, applied by spraying.

Kč2,150.47

Peroxide K1 for curing polyester resins

eshop_000021

The best in the resins we offer. Please do not try untested ones, it is risky and very costly! Recommended mixing ratio 0.8-3% depending on the ambient temperature and the thickness of the laminated part.

Kč398.60

Polyester Gelcoat White GS 2000 H - Norpol

eshop_000016

The secret of smooth surfaces. It creates a smooth visible layer depending on the surface of the mold. The surface does not require any further treatment after removal from the mold. We create the surface directly in the mold. The paintable gelcoat is a two-component system, mix 1-3 before use.

Kč514.63

Polyester gelcoat/Vorgelat/ T 30 - MGS - clear

eshop_000008/a

Gelcoat with high scratch resistance. For curing, use Peroxide SF 10, resin to peroxide mixing ratio=100:10. Workability 25min. Gel time 150min. Full curing 5-6 hours, final state after 2-3 days at room temperature. For coloring is

Kč1,445.36

Polyester gelcoat/Vorgelat/ T 35 - MGS

eshop_000010/1

Specially developed gelcoat for aircraft manufacturing with excellent parameters. Available only in white. For best results, we recommend using original peroxides and thinners. Can be diluted with SF thinner up to 10 weight parts. Pigments can be used for coloring.

Kč1,288.41

Polyester Gelcoat/Vorgelat/ T 35 SH - MGS

eshop_000010/2

Equivalent to polyester gelcoat T 35 - SH variant. The working procedure is the same as for T 35. Due to its thinner consistency, this type is particularly suitable for spray application. SH means that a thinner SH has already been added to the gelcoat.

Kč1,295.73

Polyester Resin Havelpol H 834 - REA 30W

eshop_000040/32

!!New formula - different resin color!!\n\nPolyester resin H 834 is a medium-reactive thixotropic, pre-accelerated with controlled exotherm and low shrinkage. It is intended for the production of boats and other composite parts, suitable for both manual application.

Kč316.25

Polyester Resin Polylite 32032-20

eshop_900493

It is a colorless, absolutely clear, accelerated, UV stabilized orthophthalic resin with low viscosity and reactivity. APPLICATION. Optimal curing only with Peroxide K1!! POLYLITE® 32032-20 is primarily intended for applications where extreme clarity is required.

Kč499.62

Polyester Vorgelat PC - clear, sprayable - pre-gel

900496

Vorgelat PC clear is a pre-accelerated ISO-NPG polyester gelcoat. It has been designed for combinations with epoxy laminates.\n\nIt is intended for use in the marine, construction, and transportation industries. It is also suitable for general use. It excels in resistance to water exposure.

Kč476.69

RIVERTABLE WWB Hardener

eshop_000034/1

Hardener for casting epoxy resin for creating casts with a thickness of 0-7cm. For example, pouring wooden table slabs into so-called Rivertables, etc.\n\nExcellent UV stability, clarity, colorless with the possibility of tinting using dyes and pigments

Kč723.27

Styrene for thinning polyester resins and gelcoats

eshop_000019

Styrene is one of the basic raw materials used in the production of polyester, vinylester resins, and gelcoats. It is used independently as a thinner for polyester and vinylester materials. In larger amounts, it can affect the quality and parameters of the cured

Kč245.97

Technical Acetone

eshop_010002

Very effective solvent for cleaning everything you used during laminating. It quickly dissolves polyester, epoxy, and most paints. It is very suitable for degreasing. When purchasing a 200 l drum, a refundable deposit of 1000 CZK/drum is charged for the metal drum.

Kč94.80

Thinner for epoxy spray gelcoat EG 100-W and EG 100-T

eshop_001047

Thinner for epoxy solvent-based coatings. An addition of 5-20% thinner will significantly change the viscosity of the gelcoat, making it suitable for spraying. A larger amount may significantly alter the properties of the cured gelcoat.

Kč500.72

Thinner for SF30, T 30, T 35 - MGS

eshop_000014

Manufacturer-recommended thinner for adjusting the viscosity of MGS polyester gelcoats SF 30, T 30, T 35, and T 3 PU to achieve the best results.

Kč685.20

Transparent Polyester Casting Resin

eshop_010288/1

It is a colorless, absolutely clear, accelerated, UV stabilized orthophthalic resin with low viscosity and reactivity. APPLICATION. Optimal curing only with Peroxide K1!! The transparent casting resin is primarily intended for applications where ext is required

Kč435.57

Tvrdidlo P 11 do EP 512, 531 a 371

eshop_001040

Hardener P 11 is used for curing epoxy resins in the construction industry, in the production of composites and adhesives. It is a flammable and corrosive liquid with a characteristic odor. The advantage of the hardener is its low mixing ratio, which significantly reduces costs for

Kč980.80

Two-component multipurpose adhesive Araldit AW 106(Araldit 2011)

eshop_001074/1

High-quality multipurpose adhesive with a longer processing time of approximately 120 minutes. Shear strength at 23°C (N/mm2), Tg 47°C, and operating temperature 80°C. Recommended hardener HV 953U and mixing ratio 100:80 by weight. Curing after 100 hours at 23°C.

Kč2,302.66

Vinylester Gelcoat NORPOL GM 60014 H - green molding

eshop_000020

The secret to smooth and professional molds for beautiful products. Suitable for molds laminated with polyester resin. You create the surface and details by accurately copying the model. It can be sanded and polished. Any repairs are easily feasible. Color green. dod

Kč691.79

Wax Solution 9872 3%

eshop_000033

It is used for the production of top-coats, serving to seal the final layer of the laminate as protection against UV radiation and water. The resin modified in this way does not stick after curing. 1-3% of the wax solution is added to the resin. Note, without sanding the release agent

Kč616.02