Epoxy resins, hardeners and gelcoats

Showing 37-72 of 102 item(s)

Epoxy Resin LL 201 Casting

111207

The LL 201 casting epoxy resin is a low-viscosity resin based on a mixture of bisphenol A type resins and epichlorohydrin, containing a certain amount of bifunctional epoxy alcohol as a reactive diluent. Mixing ratio 100 : 20 with hardener H 303 HT and H

Kč480.25

Epoxy Resin LR 285+ (Havel)

eshop_000000/xxx

Kč483.15

Epoxy Resin RIVERTABLE WWA

eshop_000034

Pouring epoxy resin designed primarily for creating casts with a thickness of 0-9cm. For example, pouring wooden table slabs into so-called Rivertables, etc.\n\nExcellent UV stability, clarity, colorless with the possibility of tinting using dyes and pigments, curing

Kč590.03

Epoxy Resin Surface Araldite SW 419-1

eshop_001074

Areas of use . tools for sheet forming . general mold production Processing methods Application using a brush or spatula Characteristic features . well spreadable . does not run . minimal sedimentation For curing, it is necessary to mix Hardener HV 2419 in

Kč951.67

Foam 29 x 20 mm core for hockey stick repairs SRS

eshop_900135/2

Foam for hockey stick repairs. Available in various lengths, depending on the manufacturer's supply. If the lengths differ from your request, you will be contacted.

Kč122.40

-Kč293.84

Foaming agent EE 2 /HAVEL/ for epoxy foaming resins LH 100 and LH 128

111014

Foaming agent for foaming resins LH 100 and LH 128. Mixing ratio 1-5% by weight. Always mix thoroughly before combining with the hardener. The rule applies that less agent = greater bulk density and more, conversely, less bulk density and lower strength.

Kč3,134.31 Kč3,428.15

Time left

-Kč1,067.22

Foaming Agent EP 50 /MGS/

001034

In the foaming resins L 35, L 36, and L 40, it is mixed with the foaming resin in a ratio of 100:1 to 100:3 max. up to 100:5. The foaming agent must be mixed as thoroughly as possible - preferably mechanically!

Kč3,913.14 Kč4,980.36

Time left

Foaming SYSTEM 5 for hockey stick repair, component A

111247

General: Component A is an epoxy resin modified with special black fillers, characterized by higher viscosity. It is suitable for foaming. Component B is a hardener, a mixture of technical polyalkylene polyamines, primarily containing diethylenetriamine, suitable for

Kč355.74

Foaming SYSTEM 5 for hockey stick repair, component B

111248

Component B is a hardener mixture of technical polyalkylene polyamines, primarily containing diethylenetriamine, suitable for the foaming system. Generally: Component A is an epoxy resin modified with special black color fillers, characterized by higher viscosity. It is suitable

Kč383.91

Foaming SYSTEM 5 for hockey stick repair, component C

111249

Component C is a foaming component. In general: Component A is an epoxy resin modified with special black color fillers, characterized by higher viscosity. It is suitable for foaming. Component B is a hardener, a mixture of technical polyalkylene polyamines, predominantly containing

Kč2,934.86

Hardener 133 (MGS)

eshop_001017

Hardener for curing epoxy resin L 135, L 160, L, LR, LR 10O, LH 1000, LH 130, LH 160, LH 175, LH 145 Mixing ratio is 100:35/by weight/ or 100:40/by volume/. Pot life for 100g/20 C is 10-15 min. Minimum order quantity is 25kg!

Kč933.36

Hardener 134 (MGS)

eshop_001018

Hardener for curing epoxy resin L 135, L 160, L, LR, LR 100, LH 160\nMixing ratio is 100:35 /by weight/ or 100:40 /by volume/, working time 100g / 20 C 20 min.\nFor more detailed processing instructions see tech. data sheets MGS.\nAdditional necessary info

Kč819.90

View

Hardener 135 (MGS)

eshop_001008/1

Hardener for curing epoxy resin L 135, L 160, L, LR, LR, LR 100, LH 160. The mixing ratio is 100:35/by weight/ or 100:40/by volume/. Processing time for 100g /20 C is 25-30 min. Further necessary information can be obtained at http://www.momentive.com/

Kč819.90

Hardener 136 (MGS)

eshop_001019

Hardener for curing epoxy resin L 135, L 160, L, LR, LR, LR 100, LH 160. The mixing ratio is 100:35/by weight/ or 100:40/by volume/. Processing time for 100g /20 C is 1 - 2 hours. Further necessary information can be obtained at http://www.momentive.com/

Kč948.74

Hardener 285 (MGS)

eshop_001009

Hardener for curing epoxy resin 285. The mixing ratio is 100:40 /by weight/ 100:50 /by volume/ Processing time 100g / 20 C 50 minutes. For more detailed processing instructions see the technical data sheets MGS. Additional necessary information can be obtained at http://www.moment

Kč1,172.74

Hardener 286 (MGS)

eshop_001010

Hardener for curing epoxy resin 285. The mixing ratio is 100:40 /by weight/ 100:50 /by volume/ Working time 100g / 20 C 2 h. For more detailed processing instructions see the tech. sheets MGS. Further necessary information can be obtained at http://www.momentive.c

Kč1,156.27

Hardener 287 (MGS)

eshop_001011

Hardener for curing epoxy resin 285. The mixing ratio is 100:40 /by weight/ 100:50 /by volume/ Processing time 100g / 20 C 4 h. For more detailed processing instructions see the technical data sheets MGS. Further necessary information can be obtained at http://www.momentive.c

Kč1,583.95

-Kč97.83

Hardener 500 MGS

001024

Hardener for curing epoxy resin 285 Mixing ratio is 100:40/by weight and 100:50/by volume/. Working time 100g/20 C is 10-15 min. Hardener for fast curing even at low temperatures from +10 C You can find more necessary information like this

Kč1,043.50 Kč1,141.33

Time left

Hardener 7067 for gelcoat

eshop_900883

Hardener for transparent gelcoat 7060, more information in TL and BL.

Kč1,434.82

Hardener C

eshop_001030

Hardener for curing epoxy resin C. Mixing ratio resin:hardener= 100:60 (by weight). Processing time: 50 min. Details can be found in the R+G Handbook p.77/78

Kč812.58

-Kč127.47

Hardener F 250 /MGS/

001057

Hardener for curing molding resin F 200. The mixing ratio is 100:25 /by weight/. Processing time 100g/25 C 15-20min., gel time 1 mm. 1-2 h., curing at 25 C 24 h. Hardener F 250 is suitable for use in the production of molds without the requirement for thermal curing.

Kč764.84 Kč892.31

Time left

Hardener H 10

eshop_111070

Hardener H 10 is used for curing epoxy systems with increased UV stability* primarily for casting, laminating, coating, and adhesive epoxy systems. Processing can take place at a minimum of 10°C. The advantages of the products are excellent smoothness and good surface

Kč566.61

Hardener H 100 for epoxy spray gelcoat EG 100-W and EG 100-T

eshop_001046

Hardener for epoxy gelcoats. Mixing for EG 100 T: H100= 100:40 and for EG 100 W:H100= 100:26 by weight. Mix the gelcoat and hardener in the prescribed ratio and stir thoroughly. Only then can it be diluted if necessary. Do not load until the coating is fully cured.

Kč1,200.56

Hardener H 10A

eshop_111224

Hardener H 10A is a hardener as a replacement for H10. This hardener is particularly suitable for applications where the requirement is for the clearest possible laminating system. For example, for visible layers made in the first layer from glass fabric with an aluminum surface or in case

Kč659.58

Hardener H 10B

eshop_111227

Hardener in combination with LH 160 and LH 210, ratio 100 to 47. Suitable for encapsulating self-adhesive labels. In a layer of 1-2mm, it provides a bubble-free surface. The surface stops being sticky after about 16-24 hours. Provides a clear, more flexible composite.

Kč581.98

Hardener H 145 (HAVEL)

eshop_111032

Mixing ratio 100:33, working time 50 min. Must be tempered to at least 50°C

Kč579.78

Hardener H 146

eshop_111198

High-quality hardener for curing epoxy resins. The mixing ratio with LH 160, LH 145, and LH 130 is 100:30 by weight, with a processing time of 50-60 min. The minimum curing temperature is 25 °C, but 30 °C and above is recommended.

Kč512.44

Hardener H 147 (HAVEL)

eshop_111030

Top-quality hardener for epoxy resin LH 160 recommended for the production of certified parts not only in aviation. Mixing ratio 100:25, slow hardener with a working time of 90 min. To achieve the parameters for which this hardener is recommended, it is necessary to tem

Kč566.61

Hardener H 206C

eshop_111226

Hardener H 206C is a hardener for casting epoxy resins. It is suitable for preparing clear composites for all types of laminations at temperatures above 15°C. The cured resin is not brittle and does not require conditioning, although higher thermal resistance of the cured resin can be achieved.

Kč722.53

Hardener H 25

eshop_111067

Hardener H 25 was developed as a replacement for P 11. Unlike hardener P 11, no harmful vapors are released during processing, and additionally, the cured epoxy exhibits significantly higher strengths. The hardener is suitable not only as a replacement in epoxy resins from Spolchemi

Kč629.30

Hardener H 282

eshop_112219/1

Cured polyvinyl chloride foam for the production of sandwich structures with higher thermal resistance. Panel size: 2150x1000 mm. Suitable for laminating and bonding with polyester, vinylester, or epoxy. PVC foam coated with glass, aramid, carbon or

Kč433.37

View

-Kč18.97

Hardener H 282 - for LH 288

112219/1

Hardener H 282 is a liquid low-viscosity hardener for epoxy resins. The hardener is based on cyclic diamine. For good orientation, the hardener is colored. Application: Hardener H 282 is a hardener for epoxy resins. It is suitable for all types of laminations during

Kč351.00 Kč369.97

Time left

Hardener H 285 HAVEL

eshop_111260/1

The laminating resin and hardener system was developed as a direct replacement for the well-known LR 285 system from MGS (Hexion). It is suitable for the production of composites using glass, carbon, and aramid fibers and is characterized by high static and dynamic properties.

Kč737.91

Hardener H 286 HAVEL

eshop_111091

Kč702.77

Hardener H 287 HAVEL

eshop_111260

Kč1,057.08

Hardener H 289

eshop_111118/2

Characteristics: it is a liquid hardener for epoxy resins. The hardener is based on cycloaliphatic polyamine. Physical parameters: Viscosity at 25°C 7 - 11 m Pa.s. Hydrogen equivalent 59 g Density at 20 °C 930- 960 kg/m 3 Application: Hardener H 289 is

Kč742.30