Home

Aerosil 200 - thixotropic filler for thickening resins

eshop_002042

Suitable for thickening all resins. It is used wherever it is necessary to keep the resin in a vertical position so that it does not drip. Caution: in larger volumes, overheating of the resin may occur, leading to subsequent defects. To improve mechanical properties, add

Kč499.26

Apyral - filler for polyester resins 2E

eshop_010379

Material suitable as a filler for polyester and epoxy resins. It reduces shrinkage during curing and suppresses the flammability of resin products. Can be filled up to 100:200 (Apiral 2E) at this filling, self-extinguishing properties are created. This material is from the waste

Kč258.12

Cabosil M5 (bal.10kg)

eshop_002042/1

Silica-based material. Like Aerosil 200, it is used for thickening resins and paints. Or for thixotropic modifications of these materials. Original packaging 10kg in a paper bag. It can be combined with other fillers such as microballoons, cotton in

Kč567.34

Carbon chopped fibers 3mm

eshop_003020/6

Material suitable for mixing with polyester and epoxy resins. Together with the resin and possibly other suitable fillers such as microballoons, Cabosil can fill hard-to-reach areas, or it can be used to bond necessary parts in the laminate.

Kč2,875.20

Carbon Powder - Ground Fiber

eshop_002071

Ground carbon fibers are a suitable filler for most resins. They are primarily used to enhance mechanical properties and also to ensure the dissipation of electrostatic charge.

Kč1,490.31

Catalyst for HT 33

eshop_710125/c

Catalyst for liquid silicone resin for casting molds and products. It is a firmer form of silicone that is still very flexible and tear-resistant. Suitable for larger molds or for less shape-demanding molds and products. Also, it

Kč1,827.20

Catalyst for HT 45

eshop_710146/a

Liquid catalyst suitable for casting molds and products. Processing time 10 min. Demolding time 1:20 hours. Viscosity: 8,000 cPs. This type is very popular and achieves a Shore hardness of 45 after curing. Mixing ratio 1:1(

Kč1,581.23

Catalyst for ZA 13

eshop_710123/a

Catalyst for liquid silicone resin for casting molds and products. It is a very soft type of silicone that is still very flexible and tear-resistant. Suitable for smaller molds or for geometrically demanding molds and production.

Kč1,803.77

Catalyst for ZA 22

eshop_710124/b

Catalyst for blue silicone resin. Processing time 15 min. Demolding time 1 hour. Viscosity: 5.000 cPs. This type is very popular and achieves a Shore hardness of 22 after curing. Mixing ratio 1:1 (by weight) Silicone ZA 22 is a tre

Kč1,751.43

Cotton Flakes

eshop_002048

Areas of use: production of lightweight, non-flowing adhesives, casting elements of molds and surfaces of structural molds using a mixture with 50% content of glass fiber cuttings and 50% content of cotton flakes. Volume data serves to assess the size of the supplied quantity.

Kč434.84

Fiberglass mat - marble pattern - dark gray MG 209 width 100cm

eshop_540020

The base consists of a fiberglass mat 30g/m2. After printing one of the designs, the weight increases by 5 - 10 grams/m2. Upon request, the option to choose from multiple designs.

Kč162.52

FMS - pore filler

eshop_002029/1

FMS is a pore filler for molds. It is suitable for filling the pores of molds (FMS) for molds made of fiberglass-reinforced polyester, epoxy, and other resins. It is used to fill the pores in both new molds and older molds with microporous areas and shallow surfaces.

Kč3,197.59

Formula Five - release wax-1pc -340g

eshop_002046

FORMULA FIVE- release wax for general use, which mixes carnauba wax - the most durable protection in nature - with modern polymers and hydrocarbon waxes. Silicone is added for easy application and facilitates multiple releases

Kč603.94

Frekote 700 NC - separator

eshop_002030

Semi-permanent polymer separator for multiple use for separating all thermosets and most moldable polymers. Ensures high slip where problematic mold geometry complicates polymer processing. 700-NC cures at normal

Kč1,677.13

Frekote B 15 - base separator

eshop_002029

The pore filler fills the micropores of molds and fills in fine scratches on their surface. When used together with other Frekote products, B-15 acts as an excellent base layer that enhances the provided separation capabilities. It is applied with a thin even layer.

Kč5,124.35

Frekote NC 770 - separator

eshop_002055/2

Frekote separator 770-NC is a universal release agent with high slip suitable for cases where there are problems with mold geometry. It cures quickly at room temperature and creates a glossy surface on the castings. It is applied to a clean mold surface by spraying, sh

Kč1,740.81

Glass chopped fibers 3 mm

eshop_002051

Suitable as a filler for resins and for many other applications.

Kč263.54

Glass Fiber Filler 0.2 mm

eshop_002050

Very fine filler for epoxy and polyester resins. Its advantage is the very fine grain size of 0.2mm, which, together with the use of clean glass fibers without impurities, gives the material exceptional properties. By adding this filler to the resin, you will improve

Kč467.05

Glass Fiber Mat - Aramid Pattern - Carbon. - CF 702 width 100cm

eshop_540022

The base consists of a glass mat 30g/m2. After printing one of the designs, the weight increases by 5 - 10 grams/m2. Upon request, the option to choose from multiple designs.

Kč173.35

Glass Fiber Mat - Brick Pattern - VS 302 BW Width 100cm

eshop_540021

The base consists of a glass mat 30g/m2. After printing one of the designs, the weight increases by 5 - 10 grams/m2. Upon request, the option to choose from multiple designs.

Kč167.93

Glass Fiber Mat - Marble Pattern - Light - MG 202 W width 100cm

eshop_540024

The base consists of a glass mat 30g/m2. After printing one of the designs, the weight increases by 5 - 10 grams/m2. Upon request, the option to choose from multiple designs.

Kč162.52

Glass flour (gray)

eshop_002069

Suitable as a filler for resins and for many other applications

Kč76.87

Glass mat 100 g/m2 emulsion, width 125 cm

eshop_500006/1

Glass mat suitable for the first layer on gelcoat. It is particularly suitable for more complex shapes. Emulsion mats - emulsion binder based on PVA (polyvinyl alcohol) Advantages: dissolves very quickly in styrene, allowing their use even in the production of shapes

Kč320.46

Glass mat 30 g/m2, width 100 cm

eshop_004060

Material suitable as the first and last layer of finished parts and molds. Due to its low weight, it is very flexible and suitable for very complex shapes where fabric or thicker mat cannot hold up. Designed for impregnation with polyesters and epoxies, during epoxy impregnation

Kč73.13